Formula EXPERIMENTS – Page 3 – IT'S ALL IN MY HANDS

Caffeine & Escin Eye Cream DIY

LAB NOTES & SAFETY NOTICE
For educational purposes only. Content reflects personal, non-professional formulation experiments and is not instructional.
No formula or information on this site is intended for commercial use, consumer application, or third-party use.
Accessing this content means you accept all risks and full responsibility for safety, testing, legal compliance, and outcomes.
[Full Legal Disclaimer & Safety Requirements]

Lab Note: My “Dusty” Escin Eye Cream Experiment

Hello Hello! 😀 Today I’m looking back at a formula that required a very steady hand and a bit of patience. I wanted to create a treatment specifically for the delicate eye area, focusing on puffiness and those tired mornings. yeheee!

The star of this experiment was Escin (the active from Horse Chestnut). If you’ve worked with it, you know it’s a very fine, “dusty” powder that can be a bit of a diva to incorporate. But it’s so worth it for its ability to support microcirculation! I also included Caffeine to give the skin a little “wake-up call.”

The Formula I Used:

Phase A:

Distilled Water: to 100
Glycerin: 2.0
Caffeine: 0.5 (I dissolved this in the hot water phase)
Xanthan Gum: 0.2

Phase B (The Light Lipid Phase):

Methyl Glucose Sesquistearate: 3.0 (My reliable emulsifier)
Cetyl Alcohol: 1.0 (Just a little for stability)
Argan Oil: 3.0 (Rich in Vitamin E but not too heavy)
Rice Bran Oil: 2.0
Shea Butter: 0.5 (Just a tiny touch for creaminess)

Phase C (The Active Cold Phase):

Escin: 1.0 (The “dusty” hero!)
Cornflower Water (Hydrolat): 10.0 (Soothing for the eyes)
D-Panthenol: 1.0
Tocopherol (Vitamin E): 0.5
Preservative: (According to my usual lab choice)

Notes from my Beaker:

The Caffeine Trick: I made sure to add the Caffeine to Phase A while the water was hot. It dissolves much better that way, so you don’t end up with any “crunchy” bits in your eye cream!
Handling the Escin: This was the trickiest part. Escin is very light and dusty. I found that pre-mixing it with the Cornflower Water in Phase C to create a smooth slurry made it much easier to fold into the emulsion without it flying everywhere!
The Texture: Because it’s for the eyes, I wanted it to be light. The combination of Argan and Rice Bran oil makes it sink in quickly so it doesn’t mess up my concealer later.
pH is Critical: For the eye area, I was extremely careful to check the pH. I kept it right at 6.0 to 6.5. Our eyes are much more sensitive to acidity than the rest of our face, so “neutral” is the way to go here.

Final Verdict: I’ve been using this in the mornings, and I really notice a difference in how “awake” my eyes look. The Escin and Caffeine duo is like a double espresso for the face! It’s a bit of a “picky” formula to make, but the results are so elegant. ENJOY! 😀

Hyaluronic Acid Serum for Problem Skin

Hello there! 😀

Lab Note: My “Problem Skin” Niacinamide Serum

Hello Hello! 😀 Today I’m looking back at a formula for a super simple but highly effective serum. I designed this one specifically for those “problematic skin” days—you know, when you have a bit of an oily T-zone, some mild blemishes, and maybe those annoying red marks left over from previous spots.

I have to remind myself: this isn’t a “magic cure” for serious acne. It’s just a helping hand to keep the skin hydrated and soothe that irritation. yeheee!

The Niacinamide “Trick”

The star here is Niacinamide (Vitamin B3). It’s a powerhouse for sebum and redness, but it has a secret: it’s a close friend of Nicotinic Acid. If the pH drops too low, the Niacinamide can turn into Nicotinic Acid, which causes flushing and burning—the exact opposite of “soothing!”

Because of this, I was incredibly “fussy” about the pH in my lab. My goal was a safe pH of 6–6.5. At the time, I was using the most reliable pH strips I could find, though a pH meter is definitely the “gold standard” for this!

The Formula I Used:

Water: to 100
Niacinamide: 4.0 (The blemish fighter)
Aloe Vera Powder (200:1): 0.5
Betaine (Trimethylglycine): 5.0 (The soothing powder—not the surfactant!)
Glycerin: 1.0
Sodium Hyaluronate: 0.9 (Used here as the “gelling agent” and for deep hydration)
Preservative: 1.0 (I used my Ecocert approved one)
Extras: A drop of green food-grade colorant and a hint of fragrance.

Notes from my Beaker:

The Base Mix: I started by dissolving the Aloe, Glycerin, Betaine, and preservative into the water.
The pH Balancing Act: This was the most important part. When I first measured the mix, the pH was a bit low (under 5.5). Since I didn’t want to play with Sodium Hydroxide that day, I used a clever trick: I added a tiny bit of SAP (Sodium Ascorbyl Phosphate). It’s a stable Vitamin C that is quite alkaline, so it raised my pH perfectly into that 6–6.5 “safe zone” for the Niacinamide.
Adding the Active: Once the pH was stable, I stirred in the Niacinamide. And yes… I checked the pH again! You can never be too sure when you’re avoiding that Nicotinic Acid flush.
The “Patience” Test: I poured the Sodium Hyaluronate on top. Usually, you’re supposed to just “forget about it” for a day while it hydrates into a gel. But since I have zero patience :D, I hit it with a spatula and then my immersion mixer. It worked like a charm!
The Aesthetics: I added one drop of green colorant because it just felt “right” for a soothing aloe-based serum.

Final Verdict: Even though it was a bit of a “fuss” to keep the pH exactly right, the result was a serum that felt incredibly smooth. It didn’t feel sticky, and it really helped keep my T-zone in check without any of that scary flushing. ENJOY! 🙂

Babassu Body Cream – Recipe

Hello there! 😀

Lab Note: My “Smooth as Silk” Babassu & Shea Body Cream

Today I’m sharing a recipe for a rich body cream using a new emulsifier: Methyl Glucose Distearate. I’ve found the skin feel is even lighter than the “Sesquistearate” version, so I might start testing this for face creams too! yeheee!

For this body cream, I wanted it to feel luxurious but not greasy, so I chose Babassu Oil and Shea Butter, but balanced them with Dicaprylyl Ether to give it a nice “dry” finish.

The “Secret” Allantoin Trick:

I add Allantoin to almost everything because it’s so soothing and affordable. But it can be tricky to disperse! My secret? I found that it “melts” perfectly into Hydrolyzed Proteins. Now, I always pair them together in my Phase C—no more grainy creams! 😉

The Formula I Used:

Phase A (The Gel Base):

Water: to 100
Glycerin: 5.0
Xanthan Gum: 0.2
Carbopol Ultrez 21: 0.4 (The “No-Stir” superstar!)

Phase B (The Precious Fats):

Methyl Glucose Distearate: 3.5 (The new emulsifier)
Cetyl Alcohol / Cetyl Palmitate: 0.8 / 0.7 (My thickening duo)
Shea Butter: 6.0
Babassu Oil: 8.0
Rose Hip Oil: 3.0
Dicaprylyl Ether: 3.0 (For that “dry” touch)

Phase C (The Active Finish):

Hydrolyzed Oat Proteins: 3.0
Allantoin: 0.4 (Pre-mixed into the proteins!)
Preservative (Cosgard): 1.0
Fragrance Oil: A few drops

Notes from my Beaker:

The Carbopol Ritual: I measured the Carbopol Ultrez 21 and just poured it on top of the water. Do not mix it! Just let it sit and hydrate slowly while it sits on the surface. After a few minutes, it looks like water with little whitish pieces—that’s perfect! It only becomes a gel once the pH hits 5.
The Emulsion: I heated Phase A and B to 70°C. I added the Xanthan-glycerin slurry to the water just before mixing. Then, I slowly poured Phase B into Phase A while stirring with a spatula.
The Mixer: Once they are combined, it’s time for the immersion mixer! It turns white and liquid, but the mixer is what makes the “magic” emulsification happen.
The Ice Bath: You cannot skip the cooling process or it might separate! I used an ice bath to speed things up, stirring for about 30 minutes until it reached room temperature.
The Finish: I added my Phase C (with my Allantoin-Protein mix!), checked the pH, and adjusted it to 5.5.
The Waiting Game: Because of the Cetyl Alcohol and Palmitate, the cream keeps thickening for 24-48 hours. I left it in the beaker covered with plastic wrap for two days, stirring it every now and then, before finally putting it into jars.

Final Verdict: The texture is lovely! It’s rich because of the Shea and Babassu, but the new emulsifier and the Dicaprylyl Ether keep it from feeling “heavy.” And thanks to the protein trick, the Allantoin is perfectly smooth. ENJOY! 😀 😀 😀

Amla Power – DIY Spicy Shampoo

Lab Note: “Amla Power” Spicy Shampoo (The Poetic Effect!)

Hello Hello! 😀 Instead of trying to invent a “miracle anti-gravity” cream today, I decided to focus on something I really needed: a new shampoo!

I formulated this one for the “Autumn hair loss” season. I’m not saying I found a high-tech miracle cure—I’m not even sure those exist! Instead, I used a simple trick: Spicy Essential Oils to help stimulate blood circulation in the scalp. Plus, I added the “Prince” of Indian hair care: Amla Powder!

The Amla Legend

I bought this Amla in India. There, it’s believed to do everything: strengthen follicles, stop dandruff, prevent graying, and even straighten hair! Sips water. If you know me, you know I don’t blindly believe in miracles, but I love the history of Amla, so I added it for The Poetic Effect. 🙂

A Formulator’s Warning: Adding powders to shampoo is tricky! Unless your shampoo is super thick, the powder will eventually sink to the bottom. It can also mess with stability, so I used a higher level of preservative and made a small batch (100g) to be used quickly!

The Formula: Spicy Amla Power

Phase A:

Water: to 100
Amla Powder: 0.2 (For the poetry!)
Glycerin: 3.0
Inulin: 1.0 (For smoothing)
Hydrolyzed Silk Proteins: 2.5
Preservative (Cosgard): 1.0

Phase B (The Surfactant Base):

SLES: 25.0
Coco Glucoside / Glyceryl Oleate: 2.5
Decyl Glucoside: 2.5

Phase C (The “Spice” & Conditioning):

Polyquaternium 7: 2.0 (The conditioner)
EO of Cinnamon: 10 drops
EO of Cardamom: 5 drops
EO of Sweet Orange: 5 drops

Phase D (The Thickener):

Cocamidopropyl Betaine: 10.0 (The key to the texture!)
pH adjusted to 4.5 with Citric Acid

Notes from my Beaker:

Dispersing the Amla: At first, the Amla powder just floated there, so I hit it with the immersion mixer until Phase A was uniform.
Surfactant Magic: I mixed the Phase B surfactants first. It’s always satisfying to see that thick, pearly density start to form!
One by One: I added the Phase C ingredients (Polyquat and oils) to the surfactants one at a time. I’m not very patient about bubbles :D, so there were a few, but that’s okay!
The Big Mix: I poured the watery Phase A into the thick Phase B very slowly. It became very liquid at first—but don’t panic!
The “Betaine Flip”: As soon as I added the Cocamidopropyl Betaine (Phase D), the whole thing became dense and thick like a real shampoo. It’s my favorite part of the process!

Final Verdict: It smells incredible—like a spicy tea for your head! My hair felt strong and the scalp felt “awake.” Just remember to shake it if the Amla starts to settle!

Winter Delight – Lip Rescue Balm

Hello there I AM BACK! 😀

Lab Note: The “Winter Delight” Lip Rescue (Lola’s Recipe!)

Hello Hello! 😀 Today I am sharing what is truly the best lip balm recipe I have ever tried. This isn’t my invention—it was created by Lola, the founder of the forum where I learned so much of my formulation knowledge! I’ve been making this for over two years, so it is very well tested.

The Hydration Secret

Most lip balms are 100% oil and wax. We always hear that “Shea butter hydrates,” but actually, it doesn’t! 😀 Oils create a layer that stops water from leaving, but they don’t add any new water. Eventually, your lips still end up dry.

What makes this recipe special? It actually contains a water phase! By adding honey and glycerin, we are finally giving the lips real hydration. And the best part? The ingredients are extremely easy to find!

The Formula: Winter Delight

Oil Phase:

Beeswax: 20.0 (Use yellow virgin wax for the best scent! :D)
Rice Bran Oil: 45.0
Tocopheryl Acetate (Vitamin E): 10.0
Vanillin: A tiny pinch (for that amazing aroma)

Water Phase:

Glycerin: 5.0
Honey: 20.0

Phase C:

Sweet Orange Essential Oil: 5 drops
[NEW 2026 UPDATE]: A lip-safe preservative (see notes below!)

Notes from my Beaker: The “Drop-by-Drop” Method

Modified Cold Cream: This recipe doesn’t use a traditional emulsifier. Instead, it uses the “mechanical” method. I heated the oil phase and water phase separately.
Patience is Key: Once the wax melted, I started adding the water phase DROP BY DROP into the oil. I had to stir constantly for about 30 minutes!
The Goal: I am trying to create tiny water droplets that get “trapped” and held in place as the beeswax cools and solidifies.
Spoon vs. Mixer: I tried using a mini-mixer this time, but it created too many bubbles (making it look very white). A simple spatula or spoon actually works better for a creamy, stable result. Lesson learned! 😀
Add the PRESERVATIVE
The Scent: The mix of honey, vanillin, and sweet orange is absolutely IRRESISTIBLE.

⚠️ SAFETY UPDATE: A Note on Preservatives

In the original version of this post, I mentioned that this recipe doesn’t need a preservative because the high sugar in the honey and the glycerin “occupy” the water. While that chemistry is true, I have updated my lab practice! Because we use our fingers to apply this from a tin, it’s very easy to introduce bacteria. For 100% peace of mind, I now strongly recommend adding a lip-safe or food-grade preservative. Safety first for those beautiful lips! 😀

Final Verdict: This is a creamy balm, so it won’t work in a twist-up stick—keep it in a little tin. It’s a total lifesaver for winter. ENJOY! 😀 😀 😀

Autumn Dream – Face Cream

Lab Note: My “Autumn Dream” Face Cream

Hello Hello! 😀 I finally have the recipe and pictures for the autumn cream I’m using right now. I call it my “Poetry” cream because I was feeling a bit artistic when I made it—but also because my sensitive skin needs something truly soothing as soon as the first cold weather hits.

This cream has a higher percentage of fats than my summer formulas, plus a “bouquet” of active ingredients specifically chosen to protect capillaries and calm redness. yeheee!

The Formula:

Phase A (The Gel):

Water: to 100
Glycerin: 3.0
Xanthan Gum: 0.2 (I usually prefer a mix with Carbomer, but mine expired! Xanthan alone still works, though the finish is slightly different.)

Phase B (The Emulsion):

Murumuru Butter: 0.5 (Dry skin: 2.5)
Safflower Oil: 0.5 (Dry skin: 2.5)
Methyl Glucose Sesquistearate: 3.0 (Emulsifier)
Cetyl Palmitate: 1.0 (For a soft cream feel)
Tocopherol (Vitamin E): 0.5
Propylheptyl Caprylate: 1.5 (For a super light skin feel)

Phase C (The Soothing Actives):

Oily Part: Bisabolol (0.5), Black Currant Oil (1.0), Dry Flo (0.5)
Water Part: Hydrolyzed Silk Proteins (2.0), Allantoin (0.4), Water (5.0)
Botanical Extracts: Vitis Vinifera (0.2), Raspberry (0.1), Licorice/Glycyrrhizic Acid (0.2)
Hydration: Hyaluronic Acid Gel (5.0)
Preservative: Cosgard (1.0)

Notes from my Beaker:

Extract Colors: Just a warning—plant extracts like Licorice and Vitis Vinifera are NOT white! They will change the color of your cream to a more “earthy” tone, but the soothing benefits are worth it!
The Allantoin Trick: As always, I mix the Allantoin into the Silk Proteins first. It disperses so much better this way—no crystals!
The Process: I heated Phase A and B to 70°C. I poured B into A slowly while stirring by hand, then hit it with the immersion mixer. It turns bright white immediately!
The Cooling Phase: This part is very important. I kept stirring with a spatula until it reached room temperature. While it’s hot, it looks very liquid—don’t panic! The Cetyl Palmitate only thickens as it cools (and continues for a few days).
The Final Touch: Once cool, I added the two Phase C parts, checked the pH (it hit 5.5 perfectly), and gave it one last quick pulse with the mixer to make it perfectly smooth.

Final Verdict: This is a lifesaver for winter. The Black Currant oil and Licorice extract really help my capillaries survive the cold stress. It might not stay pure white because of the extracts, but it feels like a dream on the skin. ENJOY! 😀 😀 😀

Zombie Vaccine – Lifting Eye Gel ;)

LAB NOTES & SAFETY NOTICE
These are personal experiments for educational use only— not instructions and not for commercial or consumer use. By proceeding, you assume all risks related to safety, testing, and regulatory compliance.
[Full Legal Disclaimer & Safety Requirements]

Lab Note: The “Zombie Vaccine” Eye Serum-Gel

Hello Hello! 😀 Who doesn’t look like a zombie in the morning? (Okay, maybe you don’t… but I definitely do!). I saw the name “Zombie Vaccine” on a coffee cup once and I knew I had to steal it for this lifting eye serum.

I’m calling this a serum because it’s made of 100% active ingredients! There are no fillers here—just pure hydration and “wake-up” magic for that delicate eye area. yeheee!

The Active Duo:

Caffeine: The ultimate “double espresso” for your face. It helps stimulate microcirculation to fight puffiness and those dark zombie circles.
Sodium Hyaluronate: This is the salt form of Hyaluronic Acid. Just 1 gram is enough to turn this liquid into a beautiful, thick gel. It gives a slight “lifting” effect as it dries, while pulling hydration deep into the skin.

The Formula: Zombie Vaccine

Water: to 100
Rose Water: 30.0 (Soothing and smells like a dream)
Glycerin: 3.0
Sodium Hyaluronate: 1.0 (The gelling agent)
Blueberry Powder Extract: 0.3 (Antioxidant power!)
Caffeine: 2.0 (The anti-puffiness hero)
Preservative (Cosgard): 1.0

Notes from my Beaker:

The Caffeine Challenge: Caffeine can be a bit of a diva. I mixed the water, rose water, glycerin, and caffeine together and heated it very slowly, stirring constantly. You have to make sure it’s fully dissolved—and then I prayed it wouldn’t crystallize into needles as it cooled down! 😀 (Luckily, it stayed smooth).
The “No-Stir” Gelling: Once the liquid was completely cool, I added the preservative and the blueberry extract. Then came the Sodium Hyaluronate. I just poured it on top and did not stir.
The Waiting Game: I covered the beaker with plastic wrap and walked away. I gave it a tiny mix after a few hours, but mostly I just let it sit. It takes about a day and a half for the Hyaluronate to fully hydrate into a clear, thick gel.
pH Check: I checked the pH and it was a neutral 7.0. Since it’s for the eyes, I left it right there!

Final Verdict: This serum is so refreshing in the morning! It’s light, it’s cold, and it really helps “tighten” things up so I look a bit more human and a bit less zombie. ENJOY! 😀 😀 😀

Lab Note: My “Dusty” Escin Eye Cream Experiment

The Formula I Used:

Notes from my Beaker:

Share this:

Lab Note: My “Problem Skin” Niacinamide Serum

The Niacinamide “Trick”

The Formula I Used:

Notes from my Beaker:

Share this:

Lab Note: My “Smooth as Silk” Babassu & Shea Body Cream

The “Secret” Allantoin Trick:

The Formula I Used:

Notes from my Beaker:

Share this:

Lab Note: “Amla Power” Spicy Shampoo (The Poetic Effect!)

The Amla Legend

The Formula: Spicy Amla Power

Notes from my Beaker:

Share this:

Lab Note: The “Winter Delight” Lip Rescue (Lola’s Recipe!)

The Hydration Secret

The Formula: Winter Delight

Notes from my Beaker: The “Drop-by-Drop” Method

⚠️ SAFETY UPDATE: A Note on Preservatives

Share this:

Lab Note: My “Autumn Dream” Face Cream

The Formula:

Notes from my Beaker:

Share this:

Lab Note: The “Zombie Vaccine” Eye Serum-Gel

The Active Duo:

The Formula: Zombie Vaccine

Notes from my Beaker:

Share this: